|
|
Post by NuclearBacon on Aug 8, 2007 15:39:25 GMT -5
|
|
Huck
Administrator 
Dr. FrankenWedge
Subie Addict
Posts: 288
|
Post by Huck on Aug 8, 2007 16:32:48 GMT -5
I'd say FrankenWedge could beat the 2 XT's on that page...not sure about the Forester XT that has the fastest time...but maybe him too....
But I don't have a local 1/4 mile track...(nor a good clutch)
|
|
|
|
Post by NuclearBacon on Aug 8, 2007 17:40:08 GMT -5
how much work was getting that EJ33 (EJ? ER?) into the Xt?? a lot of wiring?? hardly any?? i'd be curious to read a write up if its anywhere... does anyone know if the stuff off the old site will be recovered?? sounds like theres a lot of answers to the questions i have.... ....and everyone has been so nice about answering my stuff over again  |
|
Huck
Administrator
Dr. FrankenWedge
Subie Addict
Posts: 288
|
Post by Huck on Aug 8, 2007 19:12:33 GMT -5
how much work was getting that EJ33 (EJ? ER?) into the Xt?? a lot of wiring?? hardly any?? i'd be curious to read a write up if its anywhere... does anyone know if the stuff off the old site will be recovered?? sounds like theres a lot of answers to the questions i have.... ....and everyone has been so nice about answering my stuff over again I hate wiring, so the wiring was a pain.... but the whole swap wasn't too bad...as far as swaps go.....  but ANY swap can be a PITA, especially when putting something in where it was never meant to be.... And all the info at the old site is safe...just unaccessable right now...hopefully will be back up soon... (...Oh Christian........ :  |
|
|
|
Post by NuclearBacon on Aug 8, 2007 20:37:56 GMT -5
awesome, im looking forward to diving into that site... sounds like a lot of good good info!!!
|
|
|
|
Post by kingbobdole on Aug 9, 2007 1:31:33 GMT -5
Swaps are cake, but then I am master wiring. I built the harness for my Rx in about 10 hours time, and that's OBD2. SPFI harness take me about 8 hours and the XT 4 banger I did for Rick took somewhere abouts that too. Cannot really compare drag times. Rx runs a 15 up here which is considered fast for a N/A car.
|
|
|
|
Post by richardsubiestanley on Aug 9, 2007 9:25:19 GMT -5
Swaps are cake, but then I am master wiring. I built the harness for my Rx in about 10 hours time, and that's OBD2. SPFI harness take me about 8 hours and the XT 4 banger I did for Rick took somewhere abouts that too. Cannot really compare drag times. Rx runs a 15 up here which is considered fast for a N/A car. Thats awesome really.. I hate wiring too. I swapped a prelude dohc vtec into a turdburd accord. It was a sleeper to say the least. Endless amounts of conversion stuff. Eventually i plan on copying huck so hopefully its not as bad. |
|
|
|
Post by 86bratman on Aug 9, 2007 18:35:02 GMT -5
Thats awesome really.. I hate wiring too. I swapped a prelude dohc vtec into a turdburd accord. It was a sleeper to say the least. Endless amounts of conversion stuff. Eventually i plan on copying huck so hopefully its not as bad. I feel your pain on the h22 accord swap... I did one for a friend back in May. I'm looking forward to doing something to an xt... when I get it |
|
but ANY swap can be a PITA, especially when putting something in where it was never meant to be....
